PRODUCTS

BTMSEAL E2K F

BTMSEAL E2K F is solvent-free, two-component, filled, epoxy-based, which is made of resin and hardeners, lining material. The product has low viscosity, easy to apply, and it penetrates perfectly to the surfaces. It can be used indoor and outdoor areas, since it does not contain any solvent. After it is cured, it forms a waterproof, fraction-resistant and impermeable film. This film is impermeable and resistant to acid, base, diluted saline solutions, grease oils and petroleum products. Since A and B components are packed in measured amounts, they should be used by getting mixed together in the field of use. 

ADVANTAGES

•Perfect coating

•Perfect resistance to weather conditions

•Ability to bridge micro-cracks

•Easy-to-apply

•Resistant to fungus and algae

•Helps final material to perfectly adhere on the surface


PLACES OF USE

BTMSEAL E2K F is used on wooden and metal surfaces, as well as on mineral-based surfaces such as plaster, natural stone, concrete and cement finishes. Also can be used as;

•Lining layer in epoxy flooring applications,

•Adherence improving lining in epoxy applications,

•Lining layer before polyurethane and polyuria insulating material applications,

•Concrete strengthener on loose grounds.  


SURFACE PREPARATION

The surface should be clean, dry and flat, as well as it should be free from dirt, dust, oil, wax, mold and other materials which could negatively affect the performance of BTMSEAL E2K F.

•Any kind of loose, dust-generating, cracked, encrusted and pre-painted surfaces should be cleaned with the help of scrapping, grinding, brushing with wire brush and / or a machine (pressure water spray or sanding).

•Damaged or decomposed surfaces should be fixed by using epoxy mortar. 

•Old painted and uneven surfaces should be grinded. Polished surfaces should be grinded until they tarnish. 

•Plaster and concrete surfaces on which the material to be applied should be cured. 

•Tensile strength of concrete application surface should be minimum 1,5 N/mm², and compressive strength should be 25 N/mm². If grout bleeding occurs on concrete surfaces, the surface should be made fit for lining with the help of mechanical methods. 


APPLICATION

BTMSEAL E2K F is supplied as ready-to-use preparations according to its mixture ratio. Before starting to mix, make sure that product temperature is between +15°C and +25°C.  Component B should entirely be poured into component A and make sure that there is no material left in component B.  The materials should be mixed using an appropriate mixing paddle and a mixer operating at 300 rpm for 2-3 minutes until a homogenous mixture is obtained, in such a way that no unmixed material is left in or around the package. The mixture is applied on the surface with the help of roll or trowel. 

Wastage should be 400 - 600 gr/m² during the application. 

Application Tools:

Brush, roll, steel trowel

After application, the tools should be cleaned via appropriate solvents. (toluene, epoxy thinner, cellulosic thinner etc.) 


PACKAGING

A Component: 16 kg barrel 

B Component: 4 kg barrel


STORAGE CONDITION AND SHELFLIFE

The product should be kept in unopened original package, dry and cool places and away from frost. Appropriate storing temperature should be between +5°C - +30°C. Shelf life is 9 months as from production date under appropriate storage conditions. 


WARNINGS

Avoid applying in inadequately and poorly ventilated areas.

Can be corrosive in case of contact with skin. 

Wear gloves in order to prevent direct contact. Use protective glasses.

In case of contact with skin, wash with soap and rinse with plenty of water. 

For more information, please contact with our Technical Units. 


adres_2BTM Bitümlü Tecrit Maddeleri Sanayi ve Ticaret A.Ş. Kemalpaşa O.S.B. Mahallesi Gazi Bulvarı No:152 35730 Kemalpaşa/İzmir TURKEY Phone:+90 232 877 04 02 Fax:+90 232 877 04 10  info@btm.co • www.btm.co


MANAGEMENT SYSTEM DOCUMENTS
ISO 9001-2015 Quality Management System Certificate
8pnyQ